Skip to content

Water and wastewater

Water and Wastewater Automation and Electrical: Sector Guide

Water and wastewater automation explained: typical areas of treatment plants and pumping stations, what gets electrified and automated, and how to scope upgrades.

Direct answer

Water and wastewater automation covers the control, supervision and electrical systems of treatment plants (WTPs and WWTPs) and pumping stations. Each area, from intake to sludge handling, needs power distribution, PLC control and SCADA supervision. Authomathika works on both the electrical and automation disciplines, scoped per project.

Institutional content: Authomathika

Published:

A sanitation system is a chain of facilities, from raw water intake to treated effluent discharge, and each one depends on reliable power and control. Automation and electrical design here are about keeping pumps, valves, dosing and treatment processes running continuously, with the operator seeing what is happening. This guide gives a sector overview and points to deeper guides for each area.

What are the typical areas of a water and wastewater system?

A system is usually split into intake and raw water pumping, the water treatment plant (WTP), treated water storage and distribution pumping, sewage collection and lift stations, and the wastewater treatment plant (WWTP). A WTP is a facility that turns raw water into potable water. A WWTP is a facility that treats sewage before it returns to the environment.

AreaMain functionTypical equipment
Intake and raw water pumpingCapture and lift raw waterPumps, screens, gates, level sensors
WTPCoagulation, flocculation, settling, filtration, disinfectionDosing pumps, mixers, filters, analyzers
Booster and distribution pumpingPressure and flow to the networkPump sets, drives, flow and pressure meters
Sewage lift stationsMove sewage to the plantSubmersible pumps, level control, alarms
WWTPPreliminary, biological and sludge treatmentBlowers, aerators, clarifiers, dewatering units

For the process steps themselves, see Water Treatment Plant: Stages and How It Works.

What gets electrified in water and wastewater stations?

Electrification covers everything that brings power from the utility connection to each load: medium voltage entrance, transformers, low voltage distribution, motor control, grounding, lighting and backup. A motor control center (MCC) is a lineup of cabinets that starts, protects and monitors motors. Pumps, blowers, mixers and scrapers are the dominant loads.

Typical electrical scope includes:

  • Medium voltage switchgear and transformers, where the plant is supplied in medium voltage.
  • Low voltage distribution boards and MCCs.
  • Variable frequency drives or soft starters for pumps and blowers, chosen by process need.
  • Cable trays, conduits and grounding.
  • Backup power and uninterruptible supplies for control and instrumentation.

Design follows the applicable standards, such as ABNT NBR 5410 for low voltage installations and ABNT NBR 14039 for medium voltage, always in the current edition. Work on energized systems requires qualified personnel under NR 10 and the plant's own procedures. For panel sourcing criteria, see how to choose an industrial electrical panel supplier.

What gets automated and supervised in each area?

Automation connects field instruments and actuators to a PLC, and the PLC to a SCADA supervisory system. A PLC is a programmable logic controller that executes the control logic. SCADA is the supervisory software that gives operators screens, alarms and trends.

AreaTypical automationTypical signals
IntakePump sequencing, level controlLevel, flow, pump status
WTPDosing control, filter backwash, disinfection monitoringTurbidity, pH, residual chlorine, valve position
DistributionPump and reservoir controlPressure, flow, tank level
Lift stationsLevel based start and stop, alarmsLevel, run, fault, intrusion
WWTPAeration control, sludge handling, effluent monitoringDissolved oxygen, flow, sludge level

Remote stations normally report to a central control room, which makes communication design part of the scope. See Telemetry in Water and Wastewater: What to Monitor and Chemical Dosing in Water Plants: Control and Automation.

What environmental and operating particularities does the sector have?

The sector combines humidity, corrosive atmospheres, chemicals, submerged equipment and continuous operation. Enclosures, materials and instrument protection must match the environment, and sewage areas may have hazardous atmospheres that call for classified area practices and specialized personnel.

Key points to consider:

  1. Ingress protection and corrosion resistance of panels and field devices, especially near chemical dosing and wastewater.
  2. Distributed assets: many unmanned sites, so remote supervision and reliable communication matter.
  3. Continuous service: a stopped pump or dosing failure affects public supply or discharge compliance.
  4. Power quality and outages, which justify backup and safe restart sequences.
  5. Operator routines: screens and alarms should reflect how shifts actually work.

How do shutdowns, expansions and modernizations work?

Most water and wastewater work is brownfield: upgrading a plant that cannot stop for long. A brownfield project changes an existing installation, while greenfield builds a new one. Success depends on surveying the legacy system, planning cutovers in short windows and testing before and after the transition.

A practical sequence:

  1. Survey existing electrical and control assets and their documentation.
  2. Define scope, interfaces and acceptance tests.
  3. Pre-assemble and pre-test panels and logic offsite where possible.
  4. Execute the cutover in the planned window, with a rollback path.
  5. Commission, train operators and hand over updated documentation.

Maintenance routines also feed this planning. See Water Treatment Plant Maintenance: Electrical and Controls Checklist.

How does Authomathika work in electrical and automation?

Authomathika is an engineering integrator of electrical systems, automation and industrial assembly, founded in 1999 and based in Sertãozinho, São Paulo, Brazil. In sanitation, its public portfolio includes the SESAMM project, a water treatment plant (ETA) and wastewater treatment plant (ETE) in Mogi Mirim, São Paulo. Services and products are evaluated per scope and quote. See the electrical and automation pages, and the SESAMM project for the project's own description.

Frequently asked questions

What is the difference between a WTP and a WWTP?
A WTP treats raw water to make it potable, while a WWTP treats collected sewage before discharge. Both rely on pumping, dosing, instrumentation and continuous supervision, but their processes and instruments differ.
Do all stations need a SCADA system?
Not necessarily. Small unmanned stations may run on local PLC logic with alarms, while larger plants and networks benefit from SCADA. The choice depends on the number of sites, staffing and reporting needs.
Should pumps use variable frequency drives?
It depends on the process. Drives help when flow or pressure must vary, while soft starters or direct starting can suffice for fixed duty. Decide based on the hydraulic design and the operating profile.
Can a plant be modernized without stopping the process?
Often yes, in stages. Panels and logic can be prepared and tested in advance, and cutovers are done in short, planned windows. The legacy survey determines what is feasible.
What should I gather before requesting a proposal?
Gather single line diagrams, the equipment and I/O lists, existing PLC and SCADA details, site conditions and desired schedule. You can send the request through the contact page.
Water and Wastewater Automation and Electrical: Sector Guide | Authomathika